Content | TM Racing Factory Carbon Air Filter Box Intake Cover
For 4-Stroke Fi Models from 2015>2021
This carbon fibre air box intake cover cover replaces the original plastic item.
Strong, lightweight, beautiful, the ultimate in pure race components.
As used by the TM Racing Factory Team.
Does not include Airbox - Cover supplied only.
TM Part No': 55105 | JEMX Fuel Cap for TM Racing 4-Stroke Machines from 2015>
A billet machined aluminium fuel cap, with a larger 'finger' surface area, designed to facilitate easier removal and refitting.
Comes complete with o'ring seal. For all 2015> TM Racing 4-Stroke machines with the 'under-seat' fuel tank arrangement.
Available in red, featuring the JemX logo. | TM Racing Carbon Fibre Airboot Insert.
The TM Racing Carbon Fibre Airboot Insert is designed to add rigidity to the flexible airboot between the airbox and the carburettor.
Shaped to the exact contours of the airboot itself, this carbon insert increases rigidity to ensure that when maximum engine loading is being applied, alongside higher temperatures that may 'soften' the rubber, the airboot does not deform under vacuum and actually reduce the volume of air available to the carburettor. The carbon insert will therefore allow the engine to produce greater performance under the largest loads, maximising available power.
To fit the carbon insert the airbox / airboot assembly will have to be removed from the sub-frame and disassembled. Fitting the carbon insert into the airboot will require patience and care due to the fine and intricate construction of the carbon fibre insert. Importantly, the airboot will have to be re-sealed to the air-filter mounting plate, therefore you must ensure you clean all mating faces and remove any existing sealant before the refitting and re-assembly procedure can begin.
Please note that after fitting the carbon insert that carburettor removal / refitting will be more complex as the flexibility of the airboot - that previously aided removal / refitting - will be reduced. Do not 'force' fit the carburettor as you may damage the carbon insert. It is advised that to remove / refit the carburettor the sub-frame should be loosened and lifted slightly to give greater clearance.
Fits 125cc / 144cc / 250cc / 300cc carburettor models from 2015>2021 ( all models with the 66022.15 airboot )
TM Part No' 55104
| Meca System Aluminium Sump Guards for TM Racing 2-Stroke and 4-Stroke Machines With Aluminium Chassis'.
Cut, profiled and shaped for a tailored fit suited to each specific model. Giving increased protection to the vital areas of the sump, chassis rails and ignition / clutch cover.
Available for the following models.
2-Stroke:
T-2288 : 125cc / 144cc - 2011 >2021
T-2289 : 250cc / 300cc - 2011>2018
T-2210 : 250cc / 300cc - 2019>2021
4-Stroke:
T-2439 : 250F - 08>09 450Fi / 530Fi - 2008>2014
T-2438 : 250Fi - 2010>2014
T-2463 : 250Fi / 300Fi - 2015>2021 | SAM Racing Parts: Axle Pull Set, for full sized machines 2015>.
These axle pulls are designed to save valuable time during wheel removal and re-fitting by allowing you to grab the wheel spindle to aid extraction. Especially useful for endurance type events where saving valuable time and effort is paramount. The kit includes are pair of axle pulls, one for each axle (front and rear), fitting is completed by tightening the allen bolts to expand the internal grip, locking the axle pulls into place inside the wheel spindles securely, a stronger fixing application than 'expanding' or 'stressing' individual 'fingers' machined as part of the CNC part. Finished in Blue colouring.
Part No's:
SAM-AXPULL-2015>BL-394
| BZERK seat support available for TM Racing 2-Stroke (125cc/144cc/250cc/300cc) models from 2015>2021 featuring the 'Fresh-Air' Intake System.
This seat support bracket rivets to the original plastic seat base (seat cover removed first) to strengthen and support the seat, to reduce 'compression' of the seat itself and the resulting 'widening' of the seat on the corner areas.
The BZERK seat support has been designed to reduce the flex in the seat base under certain loads, loads that can deform the shape and structure of the seat. The deformation of the seat base - where the 'Fresh-Air' intake system channel resides on the 2-stroke - can allow the sides of the seat to be exposed from the confines of the body panels. This exposure occurs where the radiator panel and side number panel area meet and the aesthetic angle is changed on the seat itself to mirror the contours of the bodywork - the seat 'widens' under deformation, thus causing snagging and damage to seat covers in the 'corner' area by boots tops and knee braces.
This seat support bracket is made from aluminium and comes with rivets for fitting. Featuring a padded support leg that disperses the loading across the fuel tank, whilst retaining full function of the 'Fresh Air' intake system, this simple yet effective part will reduce unwanted flex and deformation helping to keep your seat covers looking better, for longer.
See the images of the BZERK seat support to understand how it works.
AVAILABLE IN NATURAL ALUMINIUM COLOUR ONLY.
BZERK:SEAT-BR.2T.M15> |